Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FLEX NORYL™ Resin WCP921A - Asia - (PPE+TPE) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for FLEX NORYL™ Resin WCP921A - Asia:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Flex Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性. - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
商品の説明文
FLEX NORYL™ WCP921A resin is a flexible, non-reinforced injection moldable blend of Polyphenylene Ether (PPE) + Styrene Ethylene Butylene Styrene (SEBS) + Polyolefin. This material contains non-halogenated flame retardant and carries a UL94 flame rating of V0 at 6mm. FLEX NORYL WCP921A resin is intended for evaluation in over-molding applications such as plugs, strain reliefs, and connectors. It has a Shore A Hardness reading of 92 and exhibits low specific gravity, very low water absorption, and dimensional stability.

UL Yellow Card Link E207780-100886805
Processing/Physical Characteristics値単位テスト基準
ASTM数据
メルトフローレイト, MFI 10 g/10min ASTM D 1238
温度 250 °C -
荷重 2.16 kg -
成形収縮率., 平行 0.4 mm/mm ASTM D 955
成形収縮率, 直角 0.4 mm/mm ASTM D 955
機械的特性値単位テスト基準
ISO データ
破壊応力 9 MPa ISO 527
破壊ひずみ 50 % ISO 527
ASTM数据
破壊応力 9 MPa ASTM D 638
破断伸び 120 % ASTM D 638
ショア硬さA 92 - ASTM D 2240
熱的特性値単位テスト基準
ISO データ
厚さhでの燃焼性 V-0 class IEC 60695-11-10
試験片の厚さ 6.0 mm -
グローワイヤ燃焼性指数 (GWFI) 850 °C IEC 60695-2-12
GWFI - 試験片の厚さ 3 mm -
グローワイヤ着火温度 (GWIT) 775 °C IEC 60695-2-13
GWIT - 試験片の厚さ 3 mm -
電気的特性.値単位テスト基準
ISO データ
比誘電率, 1MHz 2.8 - IEC 62631-2-1
誘電正接, 1MHz 60 E-4 IEC 62631-2-1
耐トラッキング性 600 - IEC 60112
ASTM数据
体積抵抗率 >1E15 Ohm*cm ASTM D 257
その他の特性.値単位テスト基準
密度 1040 kg/m³ ASTM D 792
Processing Recommendation Injection Molding値単位テスト基準
Pre-drying - Temperature 60 - 80 °C -
Pre-drying - Time 4 - 6 h -
Processing humidity ≤0.01 % -
樹脂温度 220 - 250 °C -
金型温度 40 - 60 °C -
Zone 1 180 - 220 °C -
Zone 2 210 - 240 °C -
Zone 3 220 - 250 °C -
Screw speed 30 - 80 rpm -
Back pressure 3 - 10 MPa -
特殊な特性
成形加工法.
射出成形.
添加剤.
難燃剤.
特殊な特性.
難燃.
領域別の利用可能性
アジア/太平洋地域.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.